I have modified a couple of OFW 4.82 ps3's with ps3xploit 2.0:- always made a dump- checked dump- wrote to NOR- installed CFW 4.82 RebugNow I needed to downgrade for a remarry logic board of the blueray drive (CECHL04), because of eject not working and it is related to the PCB in the bluray drive.So what I did with ps3xploit 2.0 with still original PCB in BD drive:- made dump- checked dump- wrote to NOR- from safe mode installed 'Rogero downgrader.PUP' (used that many times when using hw flasher)Everything went fine, downgrade went good. But when I installed the normal toggleqa.pkg (95KB version), I could execute it from XMB, but every time I got a black screen and no beeps. Tried many times.Later on, I have read that I should first install 4.82 CFW and toggle qa from there, but now I am on 3.55 Rogero downgraded CFW, and when I enter safe mode, I need a CFW of 9.99 or higher.I needs dehasing, resetting the tables in the syscon.Do you know, how I can proceed? I still have hardware to connect to the motherboard to rewrite the NOR and I have a valid dump of NOR when on OFW 4.82.
PS3 Jailbreak 4.82 CFW Rebug Team has actually made a decision to. Habib QA Toggle 4.21+ v1.0 by Habib - PS3 Brewology (ps3ita 4.50 dex) when i try install rebug, the update. As to QA, the Rebug Toolbox makes it easy to toggle in 4.8x. Akan melihat aktifitas Led HDD kemudian jika semua berjalan dengan baik,. How To Jailbreak PS3 4.80 CFW (CEX/DEX) for PS3 Slim and PS3 Super Slim. We are proud to represent you our latest release of PS3 Jailbreak Our team start to working on our tool just a day after when SONY PlayStation 3 And PlayStation 4 console has release new update to the market.
Yes sure, here are the md5's:PS3UPDAT.PUP: B67747F529D06544A58B50toggleqa.pkg: FB11BEC5A0DDE6600BAEE0CC36742D54The description I have found of the rogero downgrader is:3.55 Rogero Downgrader RSOD.PUP:Rogero Downgrader PUP for any PS3 CFW version back to 3.55. Features: This CFW can be installed fine from XMB Update over any CFW version ( 3.55 - 9.99 ). RSOD screen bypass patch for RSOD machines (it won't fix the RSOD but allows the PS3 to boot fine into XMB). It does have all the features from Rogero CEX-3.55 v3.7. Note: This will not downgrade OFW.and for the toggleqa.pkg:Toggle QA will SET/RESET the QA Flag and Token on any 3.41 or 3.55 firmware that has lv1 mmap and lv2 peek and poke patches (which is most of them). When you run the app it first detects if the PS3 is 3.41 or 3.55.
Next it will check if your firmware has any of the required lv1 patches already and only patch the hypervisor with the ones you need. After it finishes patching Toggle QA will check the status of the QA Flag and SET/RESET it accordingly. Then once the QA SET/RESET is done any lv1 patches made will be removed. NOTE: Every now and then it will hang on the lv1 patching stage. If it has not beeped and returned to the XMB after about 30secs you will need to reboot and try again.
You would have saved yourself a whole lot of trouble if you had simply installed Rebug 4.8x REX & remarried the BD under FSM in 4.8x using the CFW Settings links straight from XMB.As to QA, the Rebug Toolbox makes it easy to toggle in 4.8x.In your current situation, in theory you are stuck until you toggle QA successfully. Once QA is toggled, you will be able to install the fw of your choice within minimum installable firmware version constraints, no matter the warnings. Double check your steps & ensure that you are using the right QA toggler (see QA brew requirements) for your situation.In practice if for some reason you cannot find a way to toggle QA, you could patch any CFW PUP for syscon 999 & install it. For example you could patch a Rebug 4.8x REX PUP for 999 syscon, either manually or using syscon changer or using ps3 mfw builder (available in our resources section). Before I do something, I was thinking about, what could caused it, that toggle qa is not working.I have downgraded many ps3's with Rogero downgrader and after that toggle qa always worked. Sometimes not the first time, but always a second time.
I must say, that I always used Progskeet 1.0 hardware flasher.Could it be caused that I now used ps3xploit, OR, can it be caused by the fact that the controller board of the Bluray drive is not fully working?When I checked the system firmware version from XMB, it was on 3.55, but when I entered safe mode to reinstall CFW, I did see that it needed to be higher then 9.99. Started with remarry procedure, but whatever drive I take (same modelnumber) drive, it shows up with NG!Performed remarry procedure maybe 10 times in the past, always went well.
This time it did not work.But despite the NG, I could play own region Bluray movie to restore DRL files! Mmmmmmm,And also, when I executed toggleqa, I heart 3 beeps!!! Did not restart, but after performing hard reset, it did show up Debug settings, Edy Viewer under Network settings with: L2 + L1 + R1 + R2 + L3 + D-pad Down on controller.I am very happy!!
Thanks a lot for responding! Now I am going to install OFW 4.82 again for this customer. But when I wanted to install 4.82 OFW from Rogero 3.55 V3.7, in safe mode I saw that it still wanted to see a firmware of 9.99 or higher.So I install OFW 3.55. That succeeded.When I then entered safe mode, it asked for a firmware of 3.55 or higher (so strange).
Maybe I put so many firmware versions in the syscon table, the 9.99 just removed from that table?After that I installed OFW 4.82, reached 100%. System wanted to do harddisk recovery (message that it takes 2-3 hours), black screen.Will leave it on there for minutes. This is the strangest system I have ever seen.Hard reset, turned system back on, again asked to do hdd recovery (2-3 hours), choosen cancel and after that just started up fine, and I could play original games again.Somehow there is something wrong with the sw on hdd, or with the hardware of the hdd.After some tries to rebuild database, it also succeeded in recovery hdd and everything is working now, without strange things.
We encourage you to check this page from time to time for system software updates and to always maintain your system to use the latest version of the system software.For more.If your PS3 system software version is 4.55 (or later), you do not need to perform this update.